 |
 |
 |
 |
 |
 |
 |
|
Q103205 - Configuring KlasTA AERO 256K to Manual Dial with a KIV-7 using AERO |
 |
|
 |
 |
 |
KB article reference no. Q103205
Version: 1.0
Keywords: KlasTA AERO 256K, KIV-7, Manual Dial, AEROThe information in this article applies to:
KlasTA Firmware v2.02
Table of Contents |
 |
2.0
3.0
4.0Introduction
Cable Connections
Configure the KIV-7
Configure KlasTA AERO 256K
|
Table of Figures |
|
|
1.0 Introduction |
|
Figure 1. Sample Scenario Using the KIV-7 for Type-1 Encryption
This document describes how to configure a KlasTA AERO 256K connected to a KIV-7 in order to manually dial a broadband ISDN connection using four 64K INMARSAT satellite terminals. In this example, KlasTA AERO 256K uses the AERO protocol in order to multiplex the data stream from the RS-530 synchronous serial port into up to four individual 64K channels. These channels will be sent through the ISDN Output ports on the KlasTA AERO 256K connected to the INMARSAT terminals. Follow the directions in the sections below outlining the steps from the KlasTA AERO 256K configuration wizard.
Prior to beginning, ensure the following cable connections have been properly secured:
- Power cord is plugged in and KlasTA is on.
- Control Port Cable is connected to the PCs serial port.
- Control Port Cable is connected to the ‘Control’ port on the front of the KlasTA.
- Black KIV-7 cable is connected to the male RS-530 connector of the KIV-7 and the female RS-530 synchronous serial port on the KlasTA.
- ISDN cables are connected to the RJ-45 ISDN Output Ports from KlasTA AERO 256K and the ISDN ports on each M4 Terminal. For more information on the cable connections associated with KlasTA AERO 256K, refer to Application Note Q103002.
The KIV-7 has a specific sequence of settings that allow it to encrypt data using the RS-530 serial data port. Follow the instructions from Klas Application Note Q100004 in order to configure the KIV-7 so that it will work properly with KlasTA AERO 256K. Given the sensitive nature of Type-1 documentation, please contact a Klas Technical Support Representative for this Application Note.
Open the KlasTA AERO 256K configuration application on your PC. Follow the steps below to configure KlasTA AERO 256K.
Figure 2. KlasTA AERO 256K Configuration Main Screen
- Check the ‘Configure KlasTA using step-by-step wizard’ radio button. Click the ‘Next’ button to continue and move on to the next configuration screen.
Figure 3. KlasTA AERO 256K Configuration Profiles Screen
- Check the Encryption Device radio button and select KIV-7 as the Encryption Device from the pull-down menu. (Note: This parameter must be identical for the KlasTA AERO 256Ks on both sides of the call.)
Figure 4. KlasTA AERO 256K Input Device Screen
Figure 5. KlasTA AERO 256K Network Type Screen
- Select the ‘KLAS AERO’ radio button indicating that both KlasTA AERO 256Ks will be using the AERO protocol.
Figure 6. KlasTA AERO 256K Bonding Mode Screen
- Select the ‘Dial and Answer’ radio button to enable KlasTA AERO 256K to initiate the dialing sequence. Also, check the ‘Dial when you click Manual Dial in the KlasTA config window’ radio button. This option specifies that KasTA AERO 256K will only dial when you push the ‘Manual Dial’ button on the KlasTA AERO 256K Configuration Wizard Main Screen.
Figure 7. KlasTA AERO 256K Dial and Answer Screen
- Input the dial strings of the opposite KlasTA AERO 256K you would like to call. Since this is a 256K call, there are four 64K B-channels. Check the B2, B3 and B4 boxes and then enter the dial strings associated with each 64K channel. Ensure you type in ‘#’ after the last digit in the dial string indicating to the KlasTA AERO 256K that the last number has been dialed.
Figure 8. KlasTA AERO 256K Dial Parameters Screen
- The KlasTA AERO 256K 56K menu screen is designed for compatibility with H.320 Video Conferencing. The H.320 VTC protocol is based on the ISDN format and only operates at intervals of 64K and 56K. Since the Aero protocol uses one out of 64 bytes for bandwidth management, the actual throughput is 63K which will not work at the 64K H.320 variant. Therefore, when using the Aero protocol, you must use the 56K version of the H.320 VTC protocol. If you plan to conduct an H.320 VTC, check the box; otherwise, leave the box unchecked.
Figure 9. KlasTA AERO 256K H.320 VTC Screen
- The Extra Config Commands screen allows you to enter manual commands that enable seldom used features. No extra configuration commands are needed for this setup.
Figure 10. KlasTA AERO 256K Extra Configuration Commands Screen
- Review the configuration options to ensure they are correct and then click on the ‘Configure’ button to initiate the configuration sequence on the KlasTA AERO 256K.
Figure 11. KlasTA Configuration Summary Screen
- If required, KlasTA AERO 256K may initially erase and reflash the firmware needed to support AERO, as shown in Figure 12. Once the firmware change is complete, the configuration settings will be loaded into KlasTA AERO 256K, as shown in Figure 13. Click on the ‘OK’ button once the configuration sequence has successfully completed.
Figure 12. Downloading AERO Firmware Version
Figure 13. KlasTA AERO 256K Configuration Progress Screen
- If desired, click the ‘Yes’ radio button to save this configuration as a Profile. Click on the ‘Finish’ button to go back to the Main Menu.
Figure 14. KlasTA AERO 256K Save Profile Screen
- Remove the control port cable from Control Port 2 and connect it into Control Port 1 on the top level. Click the ‘Reconnect’ button on the Configuration Main Screen in order to initiate the connection to Level 1. The Configuration Main Screen should appear as it does below in Figure 15. Click on the ‘Configure’ button on the opening menu.
Figure 15. KlasTA Splitter Main Configuration Screen
- Check the ‘Configure KlasTA using step-by-step wizard’ radio button. Click the ‘Next’ button to continue and move on to the next configuration screen.
Figure 16. KlasTA Splitter Configuration Profiles Screen
Figure 17. KlasTA Splitter Input Device Screen
- Check the ‘Use default number’ radio button indicating that you will use the dial-strings configured in Step 7 and do not wish to specify any more.
Figure 18. KlasTA Splitter Dial Strings Screen
- The Extra Config Commands screen allows you to enter manual commands that enable seldom used features. No extra configuration commands are needed for this setup.
Figure 19. KlasTA Splitter Extra Configuration Commands Screen
- Review the configuration options to ensure they are correct and then click on the ‘Configure’ button to initiate the configuration sequence on the KlasTA Splitter.
Figure 20. KlasTA Splitter Configuration Summary Screen
- Review the configuration options to ensure they are correct and then click on the ‘Configure’ button to initiate the configuration sequence on the KlasTA Splitter.
Figure 21. KlasTA Splitter Configuration Progress Screen
- If desired, click the ‘Yes’ radio button to save this configuration as a Profile. Click on the ‘Finish’ button to go back to the Main Menu.
Figure 22. KlasTA Splitter Save Profile Screen
- Repeat Steps 13-20 for Level 3 in order to configure the KlasTA Splitter for ISDN Y0 Input.
- Reconnect the Control Port Cable back into the Level 2 Control Port. Click on the ‘Reconnect’ button at the bottom and return to the KlasTA Configuration Main Menu.
DISCLAIMER OF WARRANTY: THE DOCUMENT IS PROVIDED AS IS, WITHOUT WARRANTY OF ANY KIND. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, WITH RESPECT TO THE DOCUMENT AND / OR ANY ASSOCIATED ON-LINE INFORMATION, KLAS DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDED BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT.
Home | About | News | Products | Support | Distributors | Contact
